![at2020 usb drivers at2020 usb drivers](https://64.media.tumblr.com/d510b51e427d660283dcc5dcd15f0efa/4f25a2439c66b1be-80/s640x960/da508738972e371a9350b210f99f8523d05da874.jpg)
Try these ideas and you will know where to look!Ĭlick to expand.You don't need the PS400 at all if you get an interface that supplies phantom power. No bussing at all, and the socket is not connected. This will tell you if it is your computer input either faulty (unlikely) or switched off in the routing somewhere.Ī good test is to plug in a plug, with the cover off, and with it in record mode gently tap the three connections on the plug - one should make a loud buzzing. If swapping the mic still results in silence - it's looking like cabling, so try another computer. If you get audio, then the cabling is good, and you identified the mic as needing more voltage than you have available - just an unhappy accident. Find any old dynamic mic and swap it with the AT.
![at2020 usb drivers at2020 usb drivers](https://i0.wp.com/kettnercreative.com/wp-content/uploads/at2020usbplus.png)
To find out which scenario (or both!) apply - you will need to substitute devices.
![at2020 usb drivers at2020 usb drivers](https://i.ytimg.com/vi/t2YyE5QNXB8/maxresdefault.jpg)
The Behringer power supply is actually capable of 36V when used with a 12V power supply - I understand it uses a simple triple circuit, so the voltage is a little less - I don't know if the mic just gets a bit noisier (the usual result of lower voltage) or if it just gives up. The Audio Technica is a mic that needs the 48V phantom power at the design current. The wiring of the XLR to the 3.5mm plug could be wrong - maybe the audio is on the circuit with the power? Leaving the audio going nowhere. You have three conductors - the ground for the return path and screening, the mic audio - in an unbalanced format and power, usually 5V with respect to the ground. The 3.5mm connector on your computer is OK for chat with a headset or other device but there's a problem with how they work. You have a number of separate elements conspiring against you. Hopefully this post provides more detail to my situation, and I do hope that I can find a resolution soon. Assuming I am to purchase one, would this work with any of the current parts I have and could someone redirect me to a video showing evidence that it would work with a PC. Again, on my previous post, I was informed about this type of audio interface:Īt most I'm willing to spend an extra 150 dollars on an audio interface, but this is obviously something I would do as a last resort.
![at2020 usb drivers at2020 usb drivers](https://m.media-amazon.com/images/S/aplus-media/vc/2c2c9f61-bbef-4736-872a-827f52b8a34c._CR0,0,300,300_PT0_SX300__.jpg)
Assuming I were to change nothing about my setup and I were to grab said USB card, would anyone be able to tell me (perhaps through their own knowledge) if it would recognise an input on my pc.Ģ. In my previous post I asked about whether or not a USB card such as a Sabrent USB would do anything for me at all.
AT2020 USB DRIVERS PC
After testing a plethora of audio jacks located at the back of my B450 Tomohawk motherboard, including plugging it into a USB to microphone/headphone splitter (made by logitech, dont know if it has any influence), I would determine that the setup was just incapable of working.Īfter asking about if there were any possibilites to making my current setup function properly, I was told that an audio interface was problematically essential to running condenser microphones, let alone plugging them into a PC or laptop.ġ. Wasn't working on my computer when trying to plug it in. For those unaware, for the purpose of context and convenience, my previous post ( ) aimed at inquiring about why my setup involving this list of items: Okay I'm going to go into major depth in comparison to my first post on this forum.